Scroll to navigation

STRUCT USB_GADGET_DR(9) Kernel Mode Gadget API STRUCT USB_GADGET_DR(9)

NAME

struct_usb_gadget_driver - driver for usb 'slave' devices

SYNOPSIS

struct usb_gadget_driver {

char * function;
enum usb_device_speed max_speed;
int (* bind) (struct usb_gadget *gadget,struct usb_gadget_driver *driver);
void (* unbind) (struct usb_gadget *);
int (* setup) (struct usb_gadget *,const struct usb_ctrlrequest *);
void (* disconnect) (struct usb_gadget *);
void (* suspend) (struct usb_gadget *);
void (* resume) (struct usb_gadget *);
void (* reset) (struct usb_gadget *);
struct device_driver driver;
char * udc_name;
struct list_head pending;
unsigned match_existing_only:1; };

MEMBERS

char * function

String describing the gadget's function

enum usb_device_speed max_speed

Highest speed the driver handles.

int (*)(struct usb_gadget *gadget,struct usb_gadget_driver *driver) bind

the driver's bind callback

void (*)(struct usb_gadget *) unbind

Invoked when the driver is unbound from a gadget, usually from rmmod (after a disconnect is reported). Called in a context that permits sleeping.

int (*)(struct usb_gadget *,const struct usb_ctrlrequest *) setup

Invoked for ep0 control requests that aren't handled by the hardware level driver. Most calls must be handled by the gadget driver, including descriptor and configuration management. The 16 bit members of the setup data are in USB byte order. Called in_interrupt; this may not sleep. Driver queues a response to ep0, or returns negative to stall.

void (*)(struct usb_gadget *) disconnect

Invoked after all transfers have been stopped, when the host is disconnected. May be called in_interrupt; this may not sleep. Some devices can't detect disconnect, so this might not be called except as part of controller shutdown.

void (*)(struct usb_gadget *) suspend

Invoked on USB suspend. May be called in_interrupt.

void (*)(struct usb_gadget *) resume

Invoked on USB resume. May be called in_interrupt.

void (*)(struct usb_gadget *) reset

Invoked on USB bus reset. It is mandatory for all gadget drivers and should be called in_interrupt.

struct device_driver driver

Driver model state for this driver.

char * udc_name

A name of UDC this driver should be bound to. If udc_name is NULL, this driver will be bound to any available UDC.

struct list_head pending

UDC core private data used for deferred probe of this driver.

unsigned:1 match_existing_only

If udc is not found, return an error and don't add this gadget driver to list of pending driver

DESCRIPTION

Devices are disabled till a gadget driver successfully binds, which means the driver will handle setup requests needed to enumerate (and meet “chapter 9” requirements) then do some useful work.

If gadget->is_otg is true, the gadget driver must provide an OTG descriptor during enumeration, or else fail the bind call. In such cases, no USB traffic may flow until both bind returns without having called usb_gadget_disconnect, and the USB host stack has initialized.

Drivers use hardware-specific knowledge to configure the usb hardware. endpoint addressing is only one of several hardware characteristics that are in descriptors the ep0 implementation returns from setup calls.

Except for ep0 implementation, most driver code shouldn't need change to run on top of different usb controllers. It'll use endpoints set up by that ep0 implementation.

The usb controller driver handles a few standard usb requests. Those include set_address, and feature flags for devices, interfaces, and endpoints (the get_status, set_feature, and clear_feature requests).

Accordingly, the driver's setup callback must always implement all get_descriptor requests, returning at least a device descriptor and a configuration descriptor. Drivers must make sure the endpoint descriptors match any hardware constraints. Some hardware also constrains other descriptors. (The pxa250 allows only configurations 1, 2, or 3).

The driver's setup callback must also implement set_configuration, and should also implement set_interface, get_configuration, and get_interface. Setting a configuration (or interface) is where endpoints should be activated or (config 0) shut down.

(Note that only the default control endpoint is supported. Neither hosts nor devices generally support control traffic except to ep0.)

Most devices will ignore USB suspend/resume operations, and so will not provide those callbacks. However, some may need to change modes when the host is not longer directing those activities. For example, local controls (buttons, dials, etc) may need to be re-enabled since the (remote) host can't do that any longer; or an error state might be cleared, to make the device behave identically whether or not power is maintained.

AUTHOR

David Brownell <dbrownell@users.sourceforge.net>

Author.

COPYRIGHT

June 2017 Kernel Hackers Manual 4.11