Controller initialisation phase¶

twe%d: microcontroller not ready

The controller's onboard CPU is not reporting that it is ready; this may be due to either a board or system failure. Initialisation has failed.

twe%d: no attention interrupt

twe%d: can't drain AEN queue

twe%d: reset not reported

twe%d: controller errors detected

twe%d: can't drain response queue

twe%d: reset %d failed, trying again

The controller is not responding correctly to the driver's attempts to reset and initialise it. This process is retried several times.

twe%d: can't initialise controller, giving up

Several attempts to reset and initialise the controller have failed; initialisation has failed and the driver will not attach to this controller.

Driver initialisation/shutdown phase¶

twe%d: register window not available

twe%d: can't allocate register window

twe%d: can't allocate parent DMA tag

twe%d: can't allocate interrupt

twe%d: can't set up interrupt

twe%d: can't establish configuration hook

A resource allocation error occurred while initialising the driver; initialisation has failed and the driver will not attach to this controller.

twe%d: can't detect attached units

Fetching the list of attached units failed; initialisation has failed.

twe%d: error fetching capacity for unit %d

twe%d: error fetching state for unit %d

twe%d: error fetching descriptor size for unit %d

twe%d: error fetching descriptor for unit %d

twe%d: device_add_child failed

twe%d: bus_generic_attach returned %d

Creation of the disk devices failed, either due to communication problems with the adapter or due to resource shortage; attachment of one or more units may have been aborted.

Operational phase¶

twe%d: command completed - %s

A command was reported completed with a warning by the controller. The warning may be one of:

redundant/inconsequential request ignored

failed to write zeroes to LBA 0

failed to profile TwinStor zones

twe%d: command failed - %s

A command was reported as failed by the controller. The failure message may be one of:

aborted due to system command or reconfiguration

aborted

access error

access violation

device failure

controller error

timed out

invalid unit number

unit not available

undefined opcode

request incompatible with unit

invalid request

firmware error, reset requested

The command will be returned to the operating system after a fatal error.

twe%d: command failed submission - controller wedged

A command could not be delivered to the controller because the controller is unresponsive.

twe%d: AEN: <%s>

The controller has reported a change in status using an AEN (Asynchronous Event Notification). The following AENs may be reported:

queue empty

soft reset

degraded mirror

controller error

rebuild fail

rebuild done

incomplete unit

initialisation done

unclean shutdown detected

drive timeout

drive error

rebuild started

aen queue full

AENs are also queued internally for use by management tools.

twe%d: error polling for signalled AENs

The controller has reported that one or more status messages are ready for the driver, but attempting to fetch one of these has returned an error.

twe%d: AEN queue overflow, lost AEN <%s>

A status message was retrieved from the controller, but there is no more room to queue it in the driver. The message is lost (but will be printed to the console).

twe%d: missing expected status bits %s

twe%d: unexpected status bits %s

A check of the controller's status bits indicates an unexpected condition.

twe%d: host interrupt

The controller has signalled a host interrupt. This serves an unknown purpose and is ignored.

twe%d: command interrupt

The controller has signalled a command interrupt. This is not used, and will be disabled.

twe%d: controller reset in progress...

The controller is being reset by the driver. Typically this is done when the driver has determined that the controller is in an unrecoverable state.

twe%d: can't reset controller, giving up

The driver has given up on resetting the controller. No further I/O will be handled.

controller reset done, %d commands restarted

The controller was successfully reset, and outstanding commands were restarted.