NAME¶

Tdpack_params - This document briefly describes all internal parameters of Tdpack.

DESCRIPTION¶

Tdpack currently supports some fifteen parameters. The current values may be retrieved using one of the routines TDGETI, TDGETR, or TDGTRS. Parameter values may be reset using one of the routines TDSETI, TDSETR, or TDSTRS.

The Tdpack parameter descriptions appear below in alphabetical order. Each description begins with a line giving the parameter name and the intrinsic FORTRAN type of the parameter.

'CS1' - Real

Character Size 1. This is a multiplier for the sizes of all characters drawn by the routine TDLBLS.

The default value of 'CS1' is 1.

'CS2' - Real

Character Size 2. This is a multiplier for the sizes of all characters drawn by the routine TDLBLA. Exactly how it is set depends on how the current reference parallelogram has been defined. If the current reference parallelogram has sides of length 1, then it is appropriate to set

'CS2'='CS1'*MIN(UMAX-UMIN,VMAX-VMIN,WMAX-WMIN)

where UMIN, UMAX, VMIN, VMAX, WMIN, and WMAX are defined like the arguments of TDLBLS. Note that, if you call TDLBLS, it resets 'CS2' in this fashion, and it does not restore the original value before return.

The default value of 'CS2' is 1.

'FOV' - Real

When 'SET' has a non-zero value, specifying that TDINIT is to call the SPPS routine SET, then 'FOV' specifies the desired field of view, in degrees, to be seen in the projection plane; its value is used to compute appropriate values for the arguments in the call to SET.

The default value of 'FOV' is 20.

'HND' - Integer

A zero value specifies that the UVW coordinate system is to be right-handed (the default), while a non-zero value says that it is to be left-handed. Changing the value of 'HND' mostly affects the behavior of TDINIT - it changes the values of the projection coefficients precomputed and stored in TDPACK common blocks - but it also affects the behavior of the routines TDDTRI and TDLBLS; for this reason, you should not change the value of 'HND' between a call to TDINIT and an ensuing call to one of the other two routines, as this would lead to inconsistent behavior. (Most likely, you will decide what the handedness of your coordinate system is, change the value of 'HND' accordingly, and leave that value unchanged thereafter.)

The default value of 'HND' is 0, specifying a right-handed coordinate system.

'LSU', 'LSV', and 'LSW' - Real

If one or more of these three values is non-zero, then the 3-space point ('LSU','LSV','LSW') is the position of the light source assumed by TDDTRI in rendering the triangles in the triangle list.

The default values are all 0., which, by convention, specifies a light source at the position (UMID,VMID,WMID), where UMID, VMID, and WMID are as specified in the last call to TDINIT.

'SET' - Integer

If this flag is equal to 1 (the default), calling TDINIT will result in a call to the SPPS routine SET to define the mapping from the "user coordinate system" (the X/Y projection plane) to the "fractional coordinate system" (the same as the GKS NDC space); that call will be done in such a way as to give a field of view of 'FOV' degrees and to use the portion of the plotter frame defined by the internal parameters 'VPL', 'VPR', 'VPB', and 'VPT'. If 'SET' is given the value 0, no such call to SET will be done and the user will be expected to have called it. In the future, other non-zero values of 'SET' may be implemented which will result in TDINIT's doing a call to SET according to some other criterion.

The default value of 'SET' is 1, specifying that a SET call should be done by TDINIT.

'SHD' - Integer

The value of 'SHD' affects the behavior of TDDTRI when it is picking the fill color to be used for a triangle and the rendering style for the triangle implies that the color index is to be chosen by computing the angle between two vectors - the normal to the triangle and the vector from its center to the light source - and then mapping that angle into a specified range of color indices (thus shading the surface).

If the value of 'SHD' is zero, angles between 0 and 90 are mapped linearly into the specified range of color indices, from lowest to highest, while angles between 90 and 180 are mapped linearly into that same range, from highest to lowest. The effect of this is essentially to use two light sources, one at the position ('LSU','LSV','LSW') and the other at an exactly opposite position relative to the center of the triangle.

If the value of 'SHD' is non-zero, angles between 0 and 180 are mapped linearly into the specified range of color indices, from lowest to highest. The effect of this is essentially to use a single light source, at the position ('LSU','LSV','LSW').

Note that, in both cases, it is the user's responsibility to define the colors associated with the color indices in the specified range to achieve the desired effect. (Normally, the colors associated with the beginning of the range of color indices should be the lightest and the colors associated with the end of that range should be the darkest.) For help in defining colors, see the code of the examples.

The default value of 'SHD' is zero.

'STE' - Integer

When 'STE' is zero (the default), then stereo pairs are drawn using a single image plane which is perpendicular to the line joining a point midway between the eyes to the point looked at. If 'STE' is set non-zero, then the view from each eye is drawn using an image plane which is perpendicular to the line joining that eye to the point looked at. (In practice, this probably makes little difference.)

Changing this parameter changes the values of the projection coefficients precomputed by TDINIT and stored in TDPACK common blocks.

The default value of 'STE' is 0, specifying that stereo pairs should be drawn using a single image plane perpendicular to the line from the midpoint of the eyes to the point looked at.

'VPB', 'VPL', 'VPR', and 'VPT' - Real

The values of these parameters specify the positions of the bottom, left, right, and top edges, respectively, of a desired viewport within the plotter frame. Each is given a value between 0 and 1, inclusive, specifying the position as a fraction of the distance across the plotter frame from left to right or from bottom to top.

These values are used when the SPPS routine SET is called by TDINIT (which happens when the internal parameter 'SET' has a non-zero value).

The default values of 'VPB', 'VPL', 'VPR', and 'VPT' are .05, .05, .95, and .95, respectively, specifying the use of most of the plotter frame.

'Rendering-Style arrays' - Integer

The internal parameter arrays that define rendering styles are accessed using the routines TDGTRS (to get the complete definition of a specific rendering style) and TDSTRS (to redefine a specific rendering style). Sixty-four different rendering styles may be defined, indexed 1 through 64; each is defined by an array of ten quantities, seven of which are of type INTEGER (named IFC1, IFC2, IFC3, IFC4, ILC1, ILC2, and ILTD) and three of which are of type REAL (named USTP, VSTP, and WSTP). These quantities may be described as follows:

SEE ALSO¶

Online: tdclrs, tdctri, tddtri, tdgeti, tdgetr, tdgrds, tdgrid, tdgtrs, tdinit, tditri, tdlbla, tdlbls, tdline, tdlnpa, tdmtri, tdotri, tdpack, tdpara, tdplch, tdprpa, tdprpi, tdprpt, tdseti, tdsetr, tdsort, tdstri, tdstrs

COPYRIGHT¶

Copyright (C) 1987-2009
University Corporation for Atmospheric Research
The use of this Software is governed by a License Agreement.