Architecture-specific requirements¶

Each architecture ABI has its own requirements on how system call arguments are passed to the kernel. For system calls that have a glibc wrapper (e.g., most system calls), glibc handles the details of copying arguments to the right registers in a manner suitable for the architecture. However, when using syscall() to make a system call, the caller might need to handle architecture-dependent details; this requirement is most commonly encountered on certain 32-bit architectures.

For example, on the ARM architecture Embedded ABI (EABI), a 64-bit value (e.g., long long) must be aligned to an even register pair. Thus, using syscall() instead of the wrapper provided by glibc, the readahead(2) system call would be invoked as follows on the ARM architecture with the EABI in little endian mode:

syscall(SYS_readahead, fd, 0,


        (unsigned int) (offset & 0xFFFFFFFF),


        (unsigned int) (offset >> 32),


        count);

Since the offset argument is 64 bits, and the first argument (fd) is passed in r0, the caller must manually split and align the 64-bit value so that it is passed in the r2/r3 register pair. That means inserting a dummy value into r1 (the second argument of 0). Care also must be taken so that the split follows endian conventions (according to the C ABI for the platform).

Similar issues can occur on MIPS with the O32 ABI, on PowerPC and parisc with the 32-bit ABI, and on Xtensa.

Note that while the parisc C ABI also uses aligned register pairs, it uses a shim layer to hide the issue from user space.

The affected system calls are fadvise64_64(2), ftruncate64(2), posix_fadvise(2), pread64(2), pwrite64(2), readahead(2), sync_file_range(2), and truncate64(2).

This does not affect syscalls that manually split and assemble 64-bit values such as _llseek(2), preadv(2), preadv2(2), pwritev(2), and pwritev2(2). Welcome to the wonderful world of historical baggage.

Architecture calling conventions¶

Every architecture has its own way of invoking and passing arguments to the kernel. The details for various architectures are listed in the two tables below.

The first table lists the instruction used to transition to kernel mode (which might not be the fastest or best way to transition to the kernel, so you might have to refer to vdso(7)), the register used to indicate the system call number, the register(s) used to return the system call result, and the register used to signal an error.

Notas:

•

On a few architectures, a register is used as a boolean (0 indicating no error, and -1 indicating an error) to signal that the system call failed. The actual error value is still contained in the return register. On sparc, the carry bit (csr) in the processor status register (psr) is used instead of a full register. On powerpc64, the summary overflow bit (SO) in field 0 of the condition register (cr0) is used.

•

NR is the system call number.

•

For s390 and s390x, NR (the system call number) may be passed directly with svc NR if it is less than 256.

•

On SuperH additional trap numbers are supported for historic reasons, but trapa#31 is the recommended "unified" ABI.

•

The x32 ABI shares syscall table with x86-64 ABI, but there are some nuances:

•

Some architectures (namely, Alpha, IA-64, MIPS, SuperH, sparc/32, and sparc/64) use an additional register ("Retval2" in the above table) to pass back a second return value from the pipe(2) system call; Alpha uses this technique in the architecture-specific getxpid(2), getxuid(2), and getxgid(2) system calls as well. Other architectures do not use the second return value register in the system call interface, even if it is defined in the System V ABI.

The second table shows the registers used to pass the system call arguments.

Notas:

•

The mips/o32 system call convention passes arguments 5 through 8 on the user stack.

Note that these tables don't cover the entire calling convention—some architectures may indiscriminately clobber other registers not listed here.