Options¶

hpsa_allow_any=1: This option allows the driver to attempt to operate on any HP Smart Array hardware RAID controller, even if it is not explicitly known to the driver. This allows newer hardware to work with older drivers. Typically this is used to allow installation of operating systems from media that predates the RAID controller, though it may also be used to enable hpsa to drive older controllers that would normally be handled by the cciss(4) driver. These older boards have not been tested and are not supported with hpsa, and cciss(4) should still be used for these.

Supported hardware¶

The hpsa driver supports the following Smart Array boards:

    Smart Array P700M


    Smart Array P212


    Smart Array P410


    Smart Array P410i


    Smart Array P411


    Smart Array P812


    Smart Array P712m


    Smart Array P711m


    StorageWorks P1210m

Since Linux 4.14, the following Smart Array boards are also supported:

    Smart Array 5300


    Smart Array 5312


    Smart Array 532


    Smart Array 5i


    Smart Array 6400


    Smart Array 6400 EM


    Smart Array 641


    Smart Array 642


    Smart Array 6i


    Smart Array E200


    Smart Array E200i


    Smart Array E200i


    Smart Array E200i


    Smart Array E200i


    Smart Array E500


    Smart Array P400


    Smart Array P400i


    Smart Array P600


    Smart Array P700m


    Smart Array P800

Configuration details¶

To configure HP Smart Array controllers, use the HP Array Configuration Utility (either hpacuxe(8) or hpacucli(8)) or the Offline ROM-based Configuration Utility (ORCA) run from the Smart Array's option ROM at boot time.

Device nodes¶

Logical drives are accessed via the SCSI disk driver (sd(4)), tape drives via the SCSI tape driver (st(4)), and the RAID controller via the SCSI generic driver (sg(4)), with device nodes named /dev/sd*, /dev/st*, and /dev/sg*, respectively.

HPSA-specific host attribute files in /sys¶

/sys/class/scsi_host/host*/rescan

This is a write-only attribute. Writing to this attribute will cause the driver to scan for new, changed, or removed devices (e.g., hot-plugged tape drives, or newly configured or deleted logical drives, etc.) and notify the SCSI midlayer of any changes detected. Normally a rescan is triggered automatically by HP's Array Configuration Utility (either the GUI or the command-line variety); thus, for logical drive changes, the user should not normally have to use this attribute. This attribute may be useful when hot plugging devices like tape drives, or entire storage boxes containing preconfigured logical drives.

/sys/class/scsi_host/host*/firmware_revision

This attribute contains the firmware version of the Smart Array.

For example:

# cd /sys/class/scsi_host/host4
# cat firmware_revision
7.14
    

HPSA-specific disk attribute files in /sys¶

/sys/class/scsi_disk/c:b:t:l/device/unique_id

This attribute contains a 32 hex-digit unique ID for each logical drive.

For example:

# cd /sys/class/scsi_disk/4:0:0:0/device
# cat unique_id
600508B1001044395355323037570F77
    

/sys/class/scsi_disk/c:b:t:l/device/raid_level

This attribute contains the RAID level of each logical drive.

For example:

# cd /sys/class/scsi_disk/4:0:0:0/device
# cat raid_level
RAID 0
    

/sys/class/scsi_disk/c:b:t:l/device/lunid

This attribute contains the 16 hex-digit (8 byte) LUN ID by which a logical drive or physical device can be addressed. c:b:t:l are the controller, bus, target, and lun of the device.

For example:

# cd /sys/class/scsi_disk/4:0:0:0/device
# cat lunid
0x0000004000000000
    

Supported ioctl() operations¶

For compatibility with applications written for the cciss(4) driver, many, but not all of the ioctls supported by the cciss(4) driver are also supported by the hpsa driver. The data structures used by these ioctls are described in the Linux kernel source file include/linux/cciss_ioctl.h.

CCISS_DEREGDISK, CCISS_REGNEWDISK, CCISS_REGNEWD

These three ioctls all do exactly the same thing, which is to cause the driver to rescan for new devices. This does exactly the same thing as writing to the hpsa-specific host "rescan" attribute.

CCISS_GETPCIINFO

Returns PCI domain, bus, device, and function and "board ID" (PCI subsystem ID).

CCISS_GETDRIVVER

Returns driver version in three bytes encoded as:

(major_version << 16) | (minor_version << 8) |


    (subminor_version)
    

CCISS_PASSTHRU, CCISS_BIG_PASSTHRU

Allows "BMIC" and "CISS" commands to be passed through to the Smart Array. These are used extensively by the HP Array Configuration Utility, SNMP storage agents, and so on. See cciss_vol_status at http://cciss.sf.net for some examples.