This sets the default zone for connections or interfaces if the zone is not selected or specified by NetworkManager, initscripts or command line tool. The default zone is public.

Deprecated. This option is ignored and no longer used. Marks are no longer used internally.

Setting this option to yes or true unloads all firewall-related kernel modules when firewalld is stopped. The default value is no or false.

If firewalld stops, it cleans up all firewall rules. Setting this option to no or false leaves the current firewall rules untouched. The default value is yes or true.

Performs reverse path filtering (RPF) on IPv6 packets as per RFC 3704. Possible values: - strict: Performs "strict" filtering as per RFC 3704. This check verifies that the in ingress interface is the same interface that would be used to send a packet reply to the source. That is, ingress == egress. - loose: Performs "loose" filtering as per RFC 3704. This check only verifies that there is a route back to the source through any interface; even if it's not the same one on which the packet arrived. - strict-forward: This is almost identical to "loose", but does not perform RPF for packets targeted to the host (INPUT). - loose-forward: This is almost identical to "loose", but does not perform RPF for packets targeted to the host (INPUT). - no: RPF is completely disabled. The rp_filter for IPv4 is controlled using sysctl.

Note: This feature has a performance impact. In most cases the impact is not enough to cause a noticeable difference. It requires route lookups and its execution occurs before the established connections fast path. As such it can have a significant performance impact if there is a lot of traffic. It's enabled by default for security, but can be disabled if performance is a concern. Alternatively one of the variants that only does RPF on forwarded packets may be used.

If this option is disabled (it is by default), combined -restore calls are used and not individual calls to apply changes to the firewall. The use of individual calls increases the time that is needed to apply changes and to start the daemon, but is good for debugging as error messages are more specific.

Add logging rules right before reject and drop rules in the INPUT, FORWARD and OUTPUT chains for the default rules and also final reject and drop rules in zones for the configured link-layer packet type. The possible values are: all, unicast, broadcast, multicast and off. The default setting is off, which disables the logging.

Deprecated. This option is ignored and no longer used.

Selects the firewall backend implementation. Possible values are; nftables (default), or iptables. This applies to all firewalld primitives. The only exception is direct and passthrough rules which always use the traditional iptables, ip6tables, and ebtables backends.

Note: The iptables backend is deprecated. It will be removed in a future release.

Flush all runtime rules on a reload. In previous releases some runtime configuration was retained during a reload, namely; interface to zone assignment, and direct rules. This was confusing to users. To get the old behavior set this to "no". Defaults to "yes".

The policy during reload. By default, all traffic except established connections is dropped while reloading the firewall rules. This can be overridden for INPUT, FORWARD and OUTPUT. The accepted values are "DROP", "REJECT" and "ACCEPT", which then applies to all tables. Alternatively, the policy can be specified per table, like "INPUT:REJECT,FORWARD:DROP,OUTPUT:ACCEPT". Defaults to "INPUT:DROP,FORWARD:DROP,OUTPUT:DROP".

As per RFC 3964, filter IPv6 traffic with 6to4 destination addresses that correspond to IPv4 addresses that should not be routed over the public internet. Defaults to "yes".

Deprecated. This option is ignored and no longer used.

This may improve forwarded traffic throughput by enabling nftables flowtable. It is a software fastpath and avoids calling nftables rule evaluation for data packets. Its value is a space separate list of interfaces. Example value "eth0 eth1". Defaults to "off".

If set to yes, add a counter to every nftables rule. This is useful for debugging and comes with a small performance cost. Defaults to "no".

If set to yes, the generated nftables rule set will be owned exclusively by firewalld. This prevents other entities from mistakenly (or maliciously) modifying firewalld's rule set. If you intentionally modify firewalld's rules, then you will have to set this to "no". Defaults to "yes".

Developer

Developer

Developer