Scroll to navigation

IP-NEIGHBOUR(8) Linux IP-NEIGHBOUR(8)

NAME

ip-neighbour - neighbour/arp tables management.

SYNOPSIS


ip [ OPTIONS ] neigh { COMMAND | help }

ip neigh { add | del | change | replace } { ADDR [ lladdr LLADDR ] [ nud STATE ] | proxy ADDR } [ dev DEV ] [ router ] [ use ] [ managed ] [ extern_learn ]

ip neigh { show | flush } [ proxy ] [ to PREFIX ] [ dev DEV ] [ nud STATE ] [ vrf NAME ] [ nomaster ]

ip neigh get ADDR dev DEV

STATE := { permanent | noarp | stale | reachable | none | incomplete | delay | probe | failed }

DESCRIPTION

The ip neigh command manipulates neighbour objects that establish bindings between protocol addresses and link layer addresses for hosts sharing the same link. Neighbour entries are organized into tables. The IPv4 neighbour table is also known by another name - the ARP table.

The corresponding commands display neighbour bindings and their properties, add new neighbour entries and delete old ones.

add a new neighbour entry
change an existing entry
add a new entry or change an existing one

These commands create new neighbour records or update existing ones.

the protocol address of the neighbour. It is either an IPv4 or IPv6 address.

the interface to which this neighbour is attached.

indicates whether we are proxying for this neighbour entry

indicates whether neighbour is a router

this neigh entry is in "use". This option can be used to indicate to the kernel that a controller is using this dynamic entry. If the entry does not exist, the kernel will resolve it. If it exists, an attempt to refresh the neighbor entry will be triggered.

this neigh entry is "managed". This option can be used to indicate to the kernel that a controller is using this dynamic entry. In contrast to "use", if the entry does not exist, the kernel will resolve it and periodically attempt to auto-refresh the neighbor entry such that it remains in resolved state when possible.

this neigh entry was learned externally. This option can be used to indicate to the kernel that this is a controller learnt dynamic entry. Kernel will not gc such an entry.

the link layer address of the neighbour. LLADDRESS can also be null.

the state of the neighbour entry. nud is an abbreviation for 'Neighbour Unreachability Detection'. The state can take one of the following values:

the neighbour entry is valid forever and can be only be removed administratively.
the neighbour entry is valid. No attempts to validate this entry will be made but it can be removed when its lifetime expires.
the neighbour entry is valid until the reachability timeout expires.
the neighbour entry is valid but suspicious. This option to ip neigh does not change the neighbour state if it was valid and the address is not changed by this command.
this is a pseudo state used when initially creating a neighbour entry or after trying to remove it before it becomes free to do so.
the neighbour entry has not (yet) been validated/resolved.
neighbor entry validation is currently delayed.
neighbor is being probed.
max number of probes exceeded without success, neighbor validation has ultimately failed.

delete a neighbour entry

The arguments are the same as with ip neigh add, except that lladdr and nud are ignored.

Warning: Attempts to delete or manually change a noarp entry created by the kernel may result in unpredictable behaviour. Particularly, the kernel may try to resolve this address even on a NOARP interface or if the address is multicast or broadcast.

list neighbour entries
the prefix selecting the neighbours to list.

only list the neighbours attached to this device.

only list the neighbours for given VRF.

only list neighbours attached to an interface with no master.

list neighbour proxies.

only list neighbours which are not currently in use.

only list neighbour entries in this state. NUD_STATE takes values listed below or the special value all which means all states. This option may occur more than once. If this option is absent, ip lists all entries except for none and noarp.

flush neighbour entries
This command has the same arguments as show. The differences are that it does not run when no arguments are given, and that the default neighbour states to be flushed do not include permanent and noarp.

With the -statistics option, the command becomes verbose. It prints out the number of deleted neighbours and the number of rounds made to flush the neighbour table. If the option is given twice, ip neigh flush also dumps all the deleted neighbours.

lookup a neighbour entry to a destination given a device

indicates whether we should lookup a proxy neighbour entry

the prefix selecting the neighbour to query.

get neighbour entry attached to this device.

EXAMPLES

ip neighbour

Shows the current neighbour table in kernel.

ip neigh flush dev eth0

Removes entries in the neighbour table on device eth0.

ip neigh get 10.0.1.10 dev eth0

Performs a neighbour lookup in the kernel and returns a neighbour entry.

SEE ALSO

ip(8)

AUTHOR

Original Manpage by Michail Litvak <mci@owl.openwall.com>

20 Dec 2011 iproute2