Scroll to navigation

XHC-WHB04B-6(1) LinuxCNC Documentation XHC-WHB04B-6(1)

NAME

xhc-whb04b-6 - Userspace jog dial HAL component for the wireless XHC WHB04B-6 USB device.

SYNOPSIS

xhc-whb04b-6 [-h] | [-H] [OPTIONS]

DESCRIPTION

The xhc-whb04b-6 HAL component supports the XHC WHB04B-6, a 6-axis wireless USB pendant. It provides a number of push-buttons, a jogwheel, two rotary buttons for axis and speed / step selection and an ordinary LCD display.

The LCD display, having a very simple firmware interface, indicates the following listed information only. No other information, such as custom data, can be printed.

Activated axis (X, Y, Z, A, B or C). Current axis position of X, Y, Z and separately of A, B, C. Whether machine (X, Y, Z, A, B or C) or relative (X1, Y1, Z1, A1, B1 or C1) coordinates are displayed. Step size or velocity depending on the operating mode (MPG or Step or Continuous). Feedrate override Spindle Feedrate override Machine state such as reset. Battery level Wireless signal strength

The pendant display, its rotary selector switch, and the component pin names use designators x,y,z,a,b and c. While this arrangement presumes a machine configured as X, Y, Z, A, B an C, the pins can be assigned independently as required in a HAL configuration.

OPTIONS

-h, --help Prints the synopsis and the most commonly used commands.

-H Run xhc-whb04b-6 in HAL-mode instead of interactive mode. When in HAL mode commands from device will be exposed to HAL’s shred memory. Interactive mode is useful for testing device connectivity and debugging.

-s Lead + jogwheel changes the spindle override speed. Each tick will increase/decrease the spindle override.

-f MPG + jogwheel changes the feed override. Each tick will increment/decrement the feed override.

-B Add 5mm and 10mm to Step feedrate output

-t Wait with timeout for USB device then proceed, exit otherwise. Without -t the timeout is implicitly infinite.

-u, -U Show received data from device. With -U received and transmitted data will be printed. Output is prefixed with "usb".

-p Show HAL pins and HAL related messages. Output is prefixed with "hal".

-e Show captured events such as button pressed/released, jog dial, axis rotary button, and feed rotary button event. Output is prefixed with "event".

-a Enable all logging facilities without explicitly specifying each.

-c Enable checksum output which is necessary for debugging the checksum generator function. Do not rely on this feature since it will be removed once the generator is implemented.

-n Force being silent and not printing any output except of errors. This will also inhibit messages prefixed with "init".

UDEV

The xhc-whb04b-6 executable needs permission for reading the pendant’s USB device. There may be the need for additional udev rules. If so, this file /etc/udev/rules.d/99-xhc-whb04b-6.rules should be created with the single line ATTR{idProduct}=="eb93", ATTR{idVendor}=="10ce", MODE="0666", OWNER="root", GROUP="plugdev".

STANDALONE USAGE

The xhc-whb04b-6 program can be run from the command line without LinuxCNC to test a pendant. This standalone mode is used to identify the button codes produced for each button press and debug transmitted USB data.

EXAMPLES

xhc-whb04b-6 -ue

Start in userspace mode (simulation) and prints incoming USB data transfer and generated key pressed/released events.

xhc-whb04b-6 -p

Start in userspace mode (simulation) and prints HAL pin names and events distributed to HAL memory.

xhc-whb04b-6 -H

Start in HAL mode (Normal mode for real machine use).

xhc-whb04b-6 -HsfB

Start in HAL mode + Spindle Override + Feedrate Override + Big step 5/10mm).

HAL USAGE

Use the -H option to specify HAL mode and other options as required: loadusr -W xhc-whb04b-6 -HsfB

Input/Output Signals

Note: For each button an output pin is provided even if no functionality is realized with that signal. For example, to stop a running program the Stop button pin may be directly connected to halui.program.stop. However, to start/pause/resume a program, the corresponding button toggles besides whb.button.start-pause also the whb.halui.program.{run,pause,resume} signals accordingly. Note: The Spindle+/Spindle- buttons do manipulate the spindle override. The spindle speed is set with the respective combos Fn + Spindle- and FN + Spindle+.

The following tables list all in-/output pins and state which signals they are meant to be connected to.

Axis and Stepgen

Signals utilized for moving axis.

<N> ... denotes the axis number, which is of {x, y, z, a, b, c}

whb.halui.home-all (bit,out)

connect to halui.home-all, driven by M-Home Pin for requesting all axis to home. See also whb.button.m-home.

whb.halui.axis.<N>.select (bit,out)

connect to halui.axis.<N>.select Pin to select axis.

whb.axis.<N>.jog-counts (s32,out)

connect to axis.<N>.jog-counts The count pin of the jogwheel.

whb.axis.<N>.jog-enable (bit,out)

connect to axis.<N>.jog-enable If true (and in manual mode), any change to "jog-counts" will result in motion. If false, "jog-counts" is ignored.

whb.axis.<N>.jog-scale (float,out)

connect to axis.<N>.jog-scale The distance to move for each count on "jog-counts", in machine units.

whb.axis.<N>.jog-vel-mode (bit,out)

connect to axis.<N>.jog-jog-vel-mode If false the jogwheel operates in position mode. The axis will move exactly jog-scale units for each count, regardless of how long that might take. If true, the jogwheel operates in velocity mode - motion stops when the wheel stops, even if that means the commanded motion is not completed.

whb.halui.max-velocity.value (float,in)

connect to halui.max-velocity.value The maximum allowable velocity, in units per second (<N> is two digit 0-padded).

whb.halui.feed-override.scale (float,in)

connect to halui.feed-override.scale The scaling for feed override value.

whb.halui.axis.<N>.pos-feedback (float,in)

connect to halui.axis.<N>.pos-feedback Feedback axis position in machine coordinates to be displayed.

whb.halui.axis.<N>.pos-relative (float,in)

connect to halui.axis.<N>.pos-relative Commanded axis position in relative coordinates to be displayed.

Machine

Signals utilized for toggling machine status.

whb.halui.machine.on (bit,out)

connect to halui.machine.on Pin for requesting machine on.

whb.halui.machine.is-on (bit,in)

connect to halui.machine.is-on Pin that indicates machine is on.

whb.halui.machine.off (bit,out)

connect to halui.machine.off Pin for requesting machine off.

Spindle

Signals utilized for operating a spindle.

whb.halui.spindle.start (bit,out)

connect to halui.spindle.0.start Pin to start the spindle.

whb.halui.spindle.is-on (bit,in)

connect to halui.spindle.0.on Pin to indicate spindle is on (either direction).

whb.halui.spindle.stop (bit,out)

connect to halui.spindle.0.stop Pin to stop the spindle.

whb.halui.spindle.forward (bit,out)

connect to halui.spindle.0.forward Pin to make the spindle go forward.

whb.halui.spindle.reverse (bit,out)

connect to halui.spindle.0.reverse Pin to make the spindle go reverse.

whb.halui.spindle.decrease (bit,out)

connect to halui.spindle.0.decrease Pin to decrease the spindle speed.

whb.halui.spindle.increase (bit,out)

connect to halui.spindle.0.increase Pin to increase the spindle speed.

whb.halui.spindle-override.increase (bit,out)

connect to halui.spindle.0.override.increase Pin for increasing the spindle override by the amount of scale.

whb.halui.spindle-override.decrease (bit,out)

connect to halui.spindle.0.override.decrease Pin for decreasing the spindle override by the amount of scale.

whb.halui.spindle-override.value (float,in)

connect to halui.spindle.0.override.value The current spindle override value.

whb.halui.spindle-override.scale (float,in)

connect to halui.spindle.0.override.scale The current spindle scaling override value.

Feed

Signals utilized for operating spindle and feed override. The feed rotary button can serve in Continuous move x% from max velocity Step move x mm Mpg override feed/spindle the special position Lead. Continuous: In this mode jogging is performed at the selected feed rate. As long the jogwheel turns, the selected axis moves. Step: In this mode the machine moves steps * wheel_counts at the currently selected step size and the current set feed rate in machine units. If the commanded position is not reached the machine keeps moving even the jogwheel is not turning. Lead: Manipulates the spindle override.+ Mpg: Manipulates the feedrate override.+

Note: As a consequence of 3 modes from manufacturer, switching the feed rotary button back from Lead revert to Mpg mode, Mpg mode is default mode at startup. Depending on the mode before turning the rotary button, the feed override results in different values. In MPG/CON the feed rate will change to 100%, 60%, ... and so forth. In Step mode the feed rate is mm.

whb.halui.feed-override.value (float,in)

connect to halui.feed-override.value The current feed override value.

whb.halui.feed-override.decrease (bit,out)

connect to halui.feed-override.decrease Pin for decreasing the feed override by amount of scale.

whb.halui.feed-override.increase (bit,out)

connect to halui.feed-override.increase Pin for increasing the feed override by amount of scale.

whb.halui.feed-override.scale (float,out)

connect to halui.feed-override.scale Pin for setting the scale on changing the feed override.

whb.halui.max-velocity.value (float,out)

connect to halui.max-velocity.value

Program

Signals for operating program and MDI mode.

whb.halui.program.run (bit,out)

connect to halui.program.run in for running a program.

whb.halui.program.is-running (bit,in)

connect to halui.program.is-running in indicating a program is running.

whb.halui.program.pause (bit,out)

connect to halui.program.pause Pin for pausing a program.

whb.halui.program.is-paused (bit,in)

connect to halui.program.is-paused Pin indicating a program is pausing.

whb.halui.program.resume (bit,out)

connect to halui.program.resume Pin for resuming a program.

whb.halui.program.stop (bit,out)

connect to program.stop Pin for stopping a program.

whb.halui.program.is-idle (bit,in)

connect to halui.program.is-idle Pin indicating no program is running.

whb.halui.mode.auto (bit,out)

connect to halui.mode.auto Pin for requesting auto mode.

whb.halui.mode.is-auto (bit,in)

connect to halui.mode.is-auto Pin for indicating auto mode is on.

whb.halui.mode.joint (bit,out)

connect to halui.mode.joint Pin for requesting joint by joint mode.

whb.halui.mode.is-joint (bit,in)

connect to halui.mode.is-joint Pin indicating joint by joint mode is on.

whb.halui.mode.manual (bit,out)

connect to halui.mode.manual Pin for requesting manual mode.

whb.halui.mode.is-manual (bit,in)

connect to halui.mode.is-manual Pin indicating manual mode is on.

whb.halui.mode.mdi (bit,out)

connect to halui.mode.mdi Pin for requesting MDI mode.

whb.halui.mode.is-mdi (bit,in)

connect to halui.mode.is-mdi Pin indicating MDI mode is on.

whb.halui.mode.teleop (bit,out)

connect to halui.mode.teleop + Pin for requesting axis by axis mode.

whb.halui.mode.is-teleop (bit,in)

connect to halui.mode.is-teleop Pin indicating axis by axis mode is on.

Buttons

For flexibility reasons each button provides an output pin even if no functionality is realized directly with that signal. The Fn button can be combined with each other push-button. This includes also RESET, Stop, Start/Pause, Macro-10, and Step|Continuous. By default the more frequent used orange buttons are executed, whereas blue ones (whb.button.macro-<M>) by combining them with Fn (press Fn first then button).

Button macro needs to be added to your ini and needs to be edited for your own use :

[HALUI]
MDI_COMMAND=(debug,macro0)  # this one is for numbering but not used by pendant (need 1 to 16)
MDI_COMMAND=(debug,macro1)
MDI_COMMAND=(debug,macro2)
MDI_COMMAND=(debug,macro3)
MDI_COMMAND=(debug,macro4)
MDI_COMMAND=(debug,macro5)
MDI_COMMAND=(debug,macro6)
MDI_COMMAND=(debug,macro7)
MDI_COMMAND=(debug,macro8)
MDI_COMMAND=(debug,macro9)
MDI_COMMAND=(debug,macro10)
MDI_COMMAND=(debug,macro11)
MDI_COMMAND=(debug,macro12)
MDI_COMMAND=(debug,macro13)
MDI_COMMAND=(debug,macro14)
MDI_COMMAND=(debug,macro15)
MDI_COMMAND=(debug,macro16)

<M> ... denotes an arbitrary macro number which is of {1, 2, ..., 16}

whb.button.reset (bit,out)

see whb.halui.estop.{activate, reset} True one Reset button down, false otherwise. For toggling E-stop use whb.halui.estop .active and .reset.

whb.button.stop (bit,out)

see whb.halui.program.stop True on Stop button down, false otherwise. For stopping a program use whb.halui.program.stop.

whb.button.start-pause (bit,out)

see whb.halui.program.{run, pause, resume} True on Start-Pause button down, false otherwise.For toggling start-pause use whb.halui.program .run, .pause, and .resume.

whb.button.feed-plus (bit,out)

True on Feed+ button down, false otherwise.

whb.button.feed-minus (bit,out)

True on Feed- button down, false otherwise.

whb.button.spindle-plus (bit,out)

see halui.spindle.0.override.increase True on Spindle+ button down, false otherwise. This button is meant to manipulate the spindle override. For increasing the spindle override use halui.spindle.0.override.increase

whb.button.spindle-minus (bit,out)

see halui.spindle.0.override.decrease True on Spindle- button down, false otherwise. This button is meant to manipulate the spindle override.For decreasing the spindle override use halui.spindle.0.override.decrease

whb.button.m-home (bit,out)

connect to halui.home-all True on M-Home button down, false otherwise. Requests MDI mode before button pin is set. See also whb.halui.mode.mdi.

whb.button.safe-z (bit,out)

connect to halui.mdi-command-<M> True on Safe-Z button down, false otherwise. Requests MDI mode before button pin is set. See also whb.halui.mode.mdi.

whb.button.w-home (bit,out)

connect to halui.mdi-command-<M> True on W-Home button down, false otherwise. Requests MDI mode before button pin is set. See also whb.halui.mode.mdi.

whb.button.s-on-off (bit,out)

see whb.halui.spindle.{start, stop} True on S-ON/OFF button down, false otherwise.For toggling spindle on-off use halui.spindle.0.start. For toggling spindle on-off use halui.spindle.0.stop.

whb.button.fn (bit,out)

True on Fn button down, false otherwise.

whb.button.probe-z (bit,out)

connect to halui.mdi-command-<M> True on Probe-Z button down, false otherwise.Requests MDI mode before button pin is set. See also whb.halui.mode.mdi.

whb.button.macro-1 (bit,out)

connect to halui.mdi-command-<M> True on Macro-1 button (Fn + Feed+) down, false otherwise.

whb.button.macro-2 (bit,out)

connect to halui.mdi-command-<M> True on Macro-2 button (Fn + Feed-) down, false otherwise.

whb.button.macro-3 (bit,out)

see whb.halui.spindle.increase True on Macro-3 button (Fn + Spindle+) down, false otherwise. This button is meant to manipulate the spindle speed. For decreasing the spindle speed use whb.halui.spindle.increase.

whb.button.macro-4 (bit,out)

see whb.halui.spindle.decrease True on Macro-4 button down (Fn + Spindle-), false otherwise This button is meant to manipulate the spindle speed. For decreasing the spindle speed use whb.halui.spindle.decrease

whb.button.macro-5 (bit,out)

connect to halui.mdi-command-<M> True on Macro-5 button down (Fn + M-HOME), false otherwise.

whb.button.macro-6 (bit,out)

connect to halui.mdi-command-<M> True on Macro-6 button down (Fn + Safe-Z), false otherwise.

whb.button.macro-7 (bit,out)

connect to halui.mdi-command-<M> True on Macro-7 button down (Fn + W-HOME), false otherwise.

whb.button.macro-8 (bit,out)

reserved for Spindle Direction True on Macro-8 button down (Fn + S-ON/OFF), false otherwise.

whb.button.macro-9 (bit,out)

connect to halui.mdi-command-<M> True on Macro-9 button down (Fn + Probe-Z), false otherwise.

whb.button.macro-10 (bit,out)

reserved for toggle DRO Abs/rel. True on Macro-10 button down, false otherwise. Switches the display coordinates to relative coordinates.On display the axis are denoted then as X1, Y1, Z1, A1, B1 and C1. See also whb.halui.axis.<N>.pos-relative.

whb.button.macro-11 (bit,out)

connect to halui.mdi-command-<M> True on Macro-11 button down (Fn + RESET), false otherwise.

whb.button.macro-12 (bit,out)

connect to halui.mdi-command-<M> True on Macro-12 button (Fn + Stop) down, false otherwise.

whb.button.macro-13 (bit,out)

connect to halui.mdi-command-<M> rue on Macro-13 button (Fn

Start/Pause) down, false otherwise.

whb.button.macro-14 (bit,out)

connect to halui.mdi-command-<M> True on Macro-14 button (Fn + Macro-10) down, false otherwise.

whb.button.macro-15 (bit,out)

connect to halui.mdi-command-<M> True on Macro-15 button down (Fn + MPG), false otherwise.

whb.button.macro-16 (bit,out)

connect to halui.mdi-command-<M> True on Macro-16 button (Fn + Step) down, false otherwise.

whb.button.mode-continuous (bit,out)

True on Continuous mode button down, false otherwise.

whb.button.mode-step (bit,out)

True on Step mode button down, false otherwise.

Pendant

whb.pendant.is-sleeping (bit,out)

True as long pendant is in sleep mode (usually a few seconds after turned off), false otherwise.

whb.pendant.is-connected (bit,out)

True as long pendant is not in sleep mode (turned on), false otherwise.

HAL CONFIGURATION EXAMPLE

Exercise caution if using copy and paste of this example code from the online web docs. Certain characters are incompatibly encoded by the web site (minus becomes em-dash). It is safer to copy and paste from https://raw.githubusercontent.com/LinuxCNC/linuxcnc/2.8/src/hal/user_comps/xhc-whb04b-6/example-configuration.md.

#
### Hal File xhc_whb04b_6.hal Example
#
# ######################################################################
# load pendant components
# ######################################################################
loadusr -W xhc-whb04b-6 -HsfB
# ######################################################################
# pendant signal configuration
# ######################################################################
# On/Off signals
net machine.is-on                         halui.machine.is-on                   whb.halui.machine.is-on
net pdnt.machine.on                       whb.halui.machine.on                  halui.machine.on
net pdnt.machine.off                      whb.halui.machine.off                 halui.machine.off
# program related signals
net pdnt.program.is-idle                  whb.halui.program.is-idle             halui.program.is-idle
net pdnt.program.is-paused                whb.halui.program.is-paused           halui.program.is-paused
net pdnt.program-is-running               whb.halui.program.is-running          halui.program.is-running
net pdnt.program.resume                   whb.halui.program.resume              halui.program.resume
net pdnt.program.pause                    whb.halui.program.pause               halui.program.pause
net pdnt.program.run                      whb.halui.program.run                 halui.program.run
net pdnt.program.stop                     whb.halui.program.stop                halui.program.stop
# machine mode related signals
net pdnt.mode.auto                        whb.halui.mode.auto                   halui.mode.auto
net pdnt.mode.manual                      whb.halui.mode.manual                 halui.mode.manual
net pdnt.mode.mdi                         whb.halui.mode.mdi                    halui.mode.mdi
net pdnt.mode.joint                       whb.halui.mode.joint                  halui.mode.joint
net pdnt.mode.teleop                      whb.halui.mode.teleop                 halui.mode.teleop
net pdnt.mode.is-auto                     halui.mode.is-auto                    whb.halui.mode.is-auto
net pdnt.mode.is-manual                   halui.mode.is-manual                  whb.halui.mode.is-manual
net pdnt.mode.is-mdi                      halui.mode.is-mdi                     whb.halui.mode.is-mdi
net pdnt.mode.is-joint                    halui.mode.is-joint                   whb.halui.mode.is-joint
net pdnt.mode.is-teleop                   halui.mode.is-teleop                  whb.halui.mode.is-teleop
# "is-homed" axis signal for allowing pendant when machine is not homed
net pdnt.axis.X.is-homed                  halui.joint.0.is-homed                whb.halui.joint.x.is-homed
net pdnt.axis.Y.is-homed                  halui.joint.1.is-homed                whb.halui.joint.y.is-homed
net pdnt.axis.Z.is-homed                  halui.joint.2.is-homed                whb.halui.joint.z.is-homed
# "selected axis" signals
net pdnt.axis.X.select                    whb.halui.axis.x.select               halui.axis.x.select
net pdnt.axis.y.select                    whb.halui.axis.y.select               halui.axis.y.select
net pdnt.axis.Z.select                    whb.halui.axis.z.select               halui.axis.z.select
net pdnt.axis.x.jog-scale                 whb.axis.x.jog-scale                  axis.x.jog-scale
net pdnt.axis.y.jog-scale                 whb.axis.y.jog-scale                  axis.y.jog-scale
net pdnt.axis.z.jog-scale                 whb.axis.z.jog-scale                  axis.z.jog-scale
net pdnt.axis.x.jog-counts                whb.axis.x.jog-counts                 axis.x.jog-counts
net pdnt.axis.y.jog-counts                whb.axis.y.jog-counts                 axis.y.jog-counts
net pdnt.axis.z.jog-counts                whb.axis.z.jog-counts                 axis.z.jog-counts
net pdnt.axis.x.jog-enable                whb.axis.x.jog-enable                 axis.x.jog-enable
net pdnt.axis.y.jog-enable                whb.axis.y.jog-enable                 axis.y.jog-enable
net pdnt.axis.z.jog-enable                whb.axis.z.jog-enable                 axis.z.jog-enable
net pdnt.axis.x.jog-vel-mode              whb.axis.x.jog-vel-mode               axis.x.jog-vel-mode
net pdnt.axis.y.jog-vel-mode              whb.axis.y.jog-vel-mode               axis.y.jog-vel-mode
net pdnt.axis.z.jog-vel-mode              whb.axis.z.jog-vel-mode               axis.z.jog-vel-mode
# macro buttons to MDI commands
net pdnt.macro-1                          whb.button.macro-1                    halui.mdi-command-01             # use MDI command from main.ini
net pdnt.macro-2                          whb.button.macro-2                    halui.mdi-command-02             # use MDI command from main.ini or used for Hardcoded lube on/off
net pdnt.reserved.for.spindle+            whb.button.macro-3                                                     # Hardcoded for spindle+ whb.halui.spindle.increase
net pdnt.reserved.for.spindle-            whb.button.macro-4                                                     # Hardcoded for spindle- whb.halui.spindle.decrease
net pdnt.macro-5                          whb.button.macro-5                    halui.mdi-command-05             # use MDI command from main.ini
net pdnt.macro-6                          whb.button.macro-6                    halui.mdi-command-06             # use MDI command from main.ini
net pdnt.macro-7                          whb.button.macro-7                    halui.mdi-command-07             # use MDI command from main.ini
net pdnt.reserved.for.spindle.dir         whb.button.macro-8                                                     # Hardcoded for spindle direction inside pendant
net pdnt.macro-9                          whb.button.macro-9                    halui.mdi-command-09             # use MDI command from main.ini
net pdnt.reserved.for.ABS-REL             whb.button.macro-10                                                    # Hardcoded for swap Dro  Relative/Absolute
net pdnt.macro-14                         whb.button.macro-14                   halui.mdi-command-14             # use MDI command from main.ini
net pdnt.reserved.for.flood               whb.button.macro-15                                                    # Hardcoded for halui.flood on/off
net pdnt.reserved.for.mist                whb.button.macro-16                                                    # Hardcoded for halui.mist on/off
net pdnt.macro.11                         whb.button.macro-11                   halui.mdi-command-11             # use MDI command from main.ini
net pdnt.macro.12                         whb.button.macro-12                   halui.mdi-command-12             # use MDI command from main.ini
net pdnt.macro.13                         whb.button.macro-13                   halui.mdi-command-13             # use MDI command from main.ini
# flood and mist toggle signals
net  pdnt.flood.is-on                     whb.halui.flood.is-on                 halui.flood.is-on                #return signal is on or off
net  pdnt.flood.off                       whb.halui.flood.off                   halui.flood.off                  #reserved whb.button.macro-15
net  pdnt.flood.on                        whb.halui.flood.on                    halui.flood.on                   #reserved whb.button.macro-15
net  pdnt.mist.is-on                      whb.halui.mist.is-on                  halui.mist.is-on                 #return signal is on or off
net  pdnt.mist.off                        whb.halui.mist.off                    halui.mist.off                   #reserved whb.button.macro-16
net  pdnt.mist.on                         whb.halui.mist.on                     halui.mist.on                    #reserved whb.button.macro-16
#net  pdnt.lube.is-on                      whb.halui.lube.is-on                  halui.lube.is-on                 #return signal is on or off
#net  pdnt.lube.off                        whb.halui.lube.off                    halui.lube.off                   #reserved whb.button.macro-2
#net  pdnt.lube.on                         whb.halui.lube.on                     halui.lube.on                    #reserved whb.button.macro-2
# default function button signals
net pdnt.button.m-home                    whb.button.m-home                     halui.home-all                   # Homeing use built-in halui home all
net pdnt.button.safe-z                    whb.button.safe-z                     halui.mdi-command-03             # Safe-z  use MDI command from main.ini
net pdnt.button.w-home                    whb.button.w-home                     halui.mdi-command-04             # Unpark  use MDI command from main.ini
net pdnt.button.probe-z                   whb.button.probe-z                    halui.mdi-command-08             # Probe-Z use MDI command from main.ini
# unused, just exposes pendant internal status or as basic button
#net pdnt.mode-lead                        whb.halui.feed.selected-lead
#net pdnt.mode-mpg-feed                    whb.halui.feed.selected-mpg-feed
#net pdnt.mode-continuous                  whb.halui.feed.selected-continuous
#net pdnt.mode-step                        whb.halui.feed.selected-step
#net pdnt.button.mode-mpg                  whb.button.mode-continuous
#net pdnt.button.mode-step                 whb.button.mode-step
#net pdnt.button.fn                        whb.button.fn
#net pdnt.button.reset                     whb.button.reset
#net pdnt.button.stop                      whb.button.stop
#net pdnt.button.start-pause               whb.button.start-pause
#net pdnt.button.s-on-off                  whb.button.s-on-off
#net pdnt.button.spindle-plus              whb.button.spindle-plus
#net pdnt.button.spindle-minus             whb.button.spindle-minus
#net pdnt.button.feed-plus                 whb.button.feed-plus
#net pdnt.button.feed-minus                whb.button.feed-minus
# spindle related signals
net pdnt.spindle.is-on                    whb.halui.spindle.is-on               spindle.0.on
net pdnt.spindle.start                    whb.halui.spindle.start               halui.spindle.0.start
net pdnt.spindle.stop                     whb.halui.spindle.stop                halui.spindle.0.stop
net pdnt.spindle.forward                  whb.halui.spindle.forward             halui.spindle.0.forward
net pdnt.spindle.reverse                  whb.halui.spindle.reverse             halui.spindle.0.reverse
net pdnt.spindle.increase                 whb.halui.spindle.increase            halui.spindle.0.increase         # reserved whb.button.macro-3
net pdnt.spindle.decrease                 whb.halui.spindle.decrease            halui.spindle.0.decrease         # reserved whb.button.macro-4
net pdnt.spindle-speed-abs                whb.halui.spindle-speed-cmd           spindle.0.speed-out-abs          # speed cmd from motion in rpm absolute
# spindle speed override signals
net pdnt.spindle-override.scale           whb.halui.spindle-override.scale      halui.spindle.0.override.scale   # needed for both spindle+/- and spindleoverride+/- button
net pdnt.spindle.override.value           halui.spindle.0.override.value        whb.halui.spindle-override.value # GUI feed rate related signals
net pdnt.spindle.override.increase        whb.halui.spindle-override.increase   halui.spindle.0.override.increase
net pdnt.spindle.override.decrease        whb.halui.spindle-override.decrease   halui.spindle.0.override.decrease
# GUI feed rate related signals can be used when program is running moving GUI slider
net pdnt.feed-override.scale              whb.halui.feed-override.scale         halui.feed-override.scale        # needed for both FeedOverride+/- and rotary knob button
net pdnt.max-velocity.value               whb.halui.max-velocity.value          halui.max-velocity.value         # needed for Mpg mode : button feed position% * max-velocity = Mpg feedrate
# take feed override min/max values from/to the GUI
net pdnt.feed-override.value              halui.feed-override.value             whb.halui.feed-override.value    # GUI feed rate related signals
net pdnt.feed-override.increase           whb.halui.feed-override.increase      halui.feed-override.increase
net pdnt.feed-override.decrease           whb.halui.feed-override.decrease      halui.feed-override.decrease
# axis position related signals feedback
net pdnt.axis.x.pos-feedback              halui.axis.x.pos-feedback             whb.halui.axis.x.pos-feedback
net pdnt.axis.y.pos-feedback              halui.axis.y.pos-feedback             whb.halui.axis.y.pos-feedback
net pdnt.axis.z.pos-feedback              halui.axis.z.pos-feedback             whb.halui.axis.z.pos-feedback
# axis position related signals relative
net pdnt.axis.x.pos-relative              halui.axis.x.pos-relative             whb.halui.axis.x.pos-relative
net pdnt.axis.y.pos-relative              halui.axis.y.pos-relative             whb.halui.axis.y.pos-relative
net pdnt.axis.z.pos-relative              halui.axis.z.pos-relative             whb.halui.axis.z.pos-relative

SEE ALSO

xhc-whb04b-6 developer documentation on GitHub

NOTES

The CRC code function is not disclosed by the manufacturer. Thus the CRC value transmitted with each package is not checked yet. Feel free to help us enhance the component.

AUTHORS

This component was started by Raoul Rubien based on predecessor device component xhc-hb04.cc. https://github.com/machinekit/machinekit/graphs/contributors gives you a more complete list of contributors.

HISTORY

The component was developed accidentally as leisure project. The development started with the xhc-whb04 (4-axis wireless pendant) implementation as reference. 73 & many thanks to the developers who delivered provided an excellent preparatory work!

COPYRIGHT

Copyright © 2018 Raoul Rubien (github.com/rubienr) Updated for Linuxcnc 2020 by alkabal_free.fr. This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.

09/06/2022 LinuxCNC