NAME¶

App::Pinto::Command::pull - pull archives from upstream repositories

VERSION¶

version 0.14

SYNOPSIS¶

  pinto --root=REPOSITORY_ROOT pull [OPTIONS] TARGET ...

DESCRIPTION¶

This command locates packages in your upstream repositories and then pulls the distributions providing those packages into your repository and registers them on a stack. Then it recursively locates and pulls all the distributions that are necessary to satisfy their prerequisites. You can also request to directly pull particular distributions.

When locating packages, Pinto first looks at the packages that already exist in the local repository, then Pinto looks at the packages that are available on the upstream repositories.

COMMAND ARGUMENTS¶

Arguments are the targets that you want to pull. Targets can be specified as packages (with or without a version specification) or as distributions. Targets can be expressed in a number of ways, so please see "TARGETS" below for more information.

You can also pipe arguments to this command over STDIN. In that case, blank lines and lines that look like comments (i.e. starting with "#" or ';') will be ignored.

COMMAND OPTIONS¶

--cascade

!! THIS OPTION IS EXPERIMENTAL !!

When searching for a package (or one of its prerequisites), always take the latest satisfactory version of the package found amongst all the upstream repositories, rather than just taking the first satisfactory version that is found. Remember that Pinto only searches the upstream repositories when the local repository does not already contain a satisfactory version of the package.

--diff-style=STYLE

Controls the style of the diff reports. STYLE must be either "concise" or "detailed". Concise reports show only one record for each distribution added or deleted. Detailed reports show one record for every package added or deleted.

The default style is "concise". However, the default style can changed by setting the "PINTO_DIFF_STYLE" environment variable to your preferred STYLE. This variable affects the default style for diff reports generated by all other commands too.

--dry-run

Go through all the motions, but do not actually commit any changes to the repository. At the conclusion, a diff showing the changes that would have been made will be displayed. Use this option to see how upgrades would potentially impact the stack.

--no-fail

!! THIS OPTION IS EXPERIMENTAL !!

Normally, failure to pull a target (or its prerequisites) causes the command to immediately abort and rollback the changes to the repository. But if "--no-fail" is set, then only the changes caused by the failed target (and its prerequisites) will be rolled back and the command will continue processing the remaining targets.

This option is useful if you want to throw a list of targets into a repository and see which ones are problematic. Once you've fixed the broken ones, you can throw the whole list at the repository again.

--message=TEXT

-m TEXT

Use TEXT as the revision history log message. If you do not use the "--message" option or the "--use-default-message" option, then you will be prompted to enter the message via your text editor. Use the "PINTO_EDITOR" or "EDITOR" or "VISUAL" environment variables to control which editor is used. A log message is not required whenever the "--dry-run" option is set, or if the action did not yield any changes to the repository.

--pin

Pins the packages to the stack, so they cannot be changed until you unpin them. Only the packages in the requested targets will be pinned -- packages in prerequisites will not be pinned. However, you may pin them separately with the pin command if you so desire.

--recurse

--no-recurse

Recursively pull any distributions required to satisfy prerequisites for the targets. The default value for this option can be configured in the pinto.ini configuration file for the repository (it is usually set to 1). To disable recursion, use "--no-recurse".

--skip-missing-prerequisite=PACKAGE

-k PACKAGE

!! THIS OPTION IS EXPERIMENTAL !!

Skip any prerequisite with name PACKAGE if a satisfactory version cannot be found. However, a warning will be given whenever this occurrs. This option only has effect when recursively fetching prerequisites for the targets (See also the "--recurse" option). This option can be repeated.

--skip-all-missing-prerequisites

-K

!! THIS OPTION IS EXPERIMENTAL !!

Skips all missing prerequisites if a satisfactory version cannot be found. However, a warning will be given whenever this occurrs. This option will silently override the "--skip-missing-prerequisite" option and only has effect when recursively fetching prerequisites for the targets (See also the "--recurse" option).

--stack=NAME

-s NAME

Puts all the packages onto the stack with the given NAME. Defaults to the name of whichever stack is currently marked as the default stack. Use the stacks command to see the stacks in the repository.

--use-default-message

-M

Use the default value for the revision history log message. Pinto will generate a semi-informative log message just based on the command and its arguments. If you set an explicit message with "--message", the "--use- default-message" option will be silently ignored.

--with-development-prerequisites

--wd

Also pull development prerequisites so you'll have everything you need to work on those distributions, in the event that you need to patch them in the future. Be aware that most distributions do not actually declare their development prerequisites.

TARGETS¶

Targets are a compact notation that identifies the things you want to pull into your repository. Targets come in two flavors: package targets and distribution targets.

  Foo::Bar                                 # Any version of Foo::Bar
  Foo::Bar~1.2                             # Foo::Bar version 1.2 or higher
  Foo::Bar==1.2                            # Only version 1.2 of Foo::Bar
  Foo::Bar<1,2!=1.3,<=1.9                  # Complex version range

  SHAKESPEARE/King-Lear-1.2.tar.gz         # A specific distribution
  SHAKESPEARE/tragedies/Hamlet-4.2.tar.gz  # Same, but with a subdirectory

AUTHOR¶

Jeffrey Ryan Thalhammer <jeff@stratopan.com>

COPYRIGHT AND LICENSE¶

This software is copyright (c) 2015 by Jeffrey Ryan Thalhammer.

This is free software; you can redistribute it and/or modify it under the same terms as the Perl 5 programming language system itself.