table of contents
| (1) | General Commands Manual | (1) |
NAME¶
pyocd-gdbserver - ARM Cortex-M programming tool
DESCRIPTION¶
pyocd-gdbserver is an ARM Cortex-M programming tool
Summary¶
pyOCD is an Open Source python based library for programming and debugging ARM Cortex-M microcontrollers using CMSIS-DAP.
Includes support for flashing new binaries, resetting the device, halt, step, resume read/write memory and set/remove breakpoints.
Support¶
Firmware files included in the upstream source are NOT included in the Debian package due to a lack of source code. Target files can be downloaded separately from https://github.com/mbedmicro/pyOCD/tree/master/binaries
Available targets for use with --target option: lpc824, kinetis, w7500, kv11z7, lpc4088qsb, kv10z7, k20d50m, ncs36510, kl28z, kl25z, k82f25615, k28f15, maxwsnenv, max32600mbed, k22fa12, lpc4088, lpc4330, ke18f16, kl46z, stm32f103rc, kl82z7, lpc54114, kl43z4, kl26z, lpc11xx_32, lpc800, rtl8195am, kl05z, lpc1768, kw41z4, lpc4088dm, stm32f051, cortex_m, lpc11u24, kl02z, kw01z4, k64f, k22f, ke15z7, nrf51, nrf52, kl27z4, kw40z4, k66f18
Usage¶
- usage: pyocd-gdbserver [-h] [--version] [-p PORT_NUMBER] [-T TELNET_PORT] [--allow-remote] [-b BOARD_ID] [-l] [--list-targets]
- [--json] [-d LEVEL] [-t TARGET] [-n] [-r] [-C VECTOR_CATCH] [-s] [-f FREQUENCY] [-o] [-bh] [-ce | -se] [-u] [-hp] [-fp] [-S] [-G] [-c CMD [CMD ...]] [-da DAPARG [DAPARG ...]]
PyOCD GDB Server
- -h, --help
- show this help message and exit
- --version
- show program's version number and exit
- -p PORT_NUMBER, --port PORT_NUMBER
- Write the port number that GDB server will open.
- -T TELNET_PORT, --telnet-port TELNET_PORT
- Specify the telnet port for semihosting.
- --allow-remote
- Allow remote TCP/IP connections (default is no).
- -b BOARD_ID, --board BOARD_ID
- Connect to board by board id. Use -l to list all connected boards.
- -l, --list
- List all connected boards.
- --list-targets
- List all available targets.
- --json
- Output lists in JSON format. Only applies to --list and --list-targets.
- -d LEVEL, --debug LEVEL
- Set the level of system logging output. Supported choices are: debug, info, warning, critical, error
- -t TARGET, --target TARGET
- Override target to debug. -n, --nobreak Disable halt at hardfault handler. (Deprecated)
- -r, --reset-break
- Halt the target when reset. (Deprecated)
- -C VECTOR_CATCH, --vector-catch VECTOR_CATCH Enable vector catch sources, one letter per enabled source in any order, or 'all' or 'none'. (h=hard
- fault, b=bus fault, m=mem fault, i=irq err, s=state err, c=check err, p=nocp, r=reset, a=all, n=none). (Default is hard fault.)
- -s, --step-int
- Allow single stepping to step into interrupts.
- -f FREQUENCY, --frequency FREQUENCY
- Set the SWD clock frequency in Hz.
- -o, --persist
- Keep GDB server running even after remote has detached.
- -bh, --soft-bkpt-as-hard
- Replace software breakpoints with hardware breakpoints.
- -ce, --chip_erase
- Use chip erase when programming.
- -se, --sector_erase
- Use sector erase when programming.
- -u, --unlock
- Unlock the device.
- -hp, --hide_progress
- Don't display programming progress.
- -fp, --fast_program
- Use only the CRC of each page to determine if it already has the same data.
- -S, --semihosting
- Enable semihosting.
- -G, --gdb-syscall
- Use GDB syscalls for semihosting file I/O.
-c CMD [CMD ...], --command CMD [CMD ...] Run command (OpenOCD compatibility).
-da DAPARG [DAPARG ...], --daparg DAPARG [DAPARG ...] Send setting to DAPAccess layer.
COPYRIGHT¶
2006-2013 ARM Limited
| 0.12.0 |