NAME¶

Smokeping::probes::DismanPing - DISMAN-PING-MIB Probe for SmokePing

SYNOPSIS¶

 *** Probes ***
 +DismanPing
 offset = 50%
 pings = 15
 step = 300
 # The following variables can be overridden in each target section
 /^influx_.+/ = influx_location = In the basement
 ownerindex = smokeping
 packetsize = 56
 pinghost = pinger@router.example.com # mandatory
 pingsrc = 192.0.2.9
 # [...]
 *** Targets ***
 probe = DismanPing # if this should be the default probe
 # [...]
 + mytarget
 # probe = DismanPing # if the default probe is something else
 host = my.host
 /^influx_.+/ = influx_location = In the basement
 ownerindex = smokeping
 packetsize = 56
 pinghost = pinger@router.example.com # mandatory
 pingsrc = 192.0.2.9

DESCRIPTION¶

Uses the DISMAN-PING-MIB to cause a remote system to send probes.

VARIABLES¶

Supported probe-specific variables:

offset

If you run many probes concurrently you may want to prevent them from hitting your network all at the same time. Using the probe-specific offset parameter you can change the point in time when each probe will be run. Offset is specified in % of total interval, or alternatively as 'random', and the offset from the 'General' section is used if nothing is specified here. Note that this does NOT influence the rrds itself, it is just a matter of when data acquisition is initiated. (This variable is only applicable if the variable 'concurrentprobes' is set in the 'General' section.)

Example value: 50%

pings

How many pings should be sent to each target. Note that the maximum value for DismanPing MIP is 15, which is less than the SmokePing default, so this class has its own default value. If your Database section specifies a value less than 15, you must also set it for this probe. Note that the number of pings in the RRD files is fixed when they are originally generated, and if you change this parameter afterwards, you'll have to delete the old RRD files or somehow convert them.

Example value: 15

Default value: 15

step

Duration of the base interval that this probe should use, if different from the one specified in the 'Database' section. Note that the step in the RRD files is fixed when they are originally generated, and if you change the step parameter afterwards, you'll have to delete the old RRD files or somehow convert them. (This variable is only applicable if the variable 'concurrentprobes' is set in the 'General' section.)

Example value: 300

Supported target-specific variables:

/^influx_.+/

This is a tag that will be sent to influxdb and has no impact on the probe measurement. The tag name will be sent without the "influx_" prefix, which will be replaced with "tag_" instead. Tags can be used for filtering.

Example value: influx_location = In the basement

ownerindex

The SNMP OwnerIndex to use when setting up the test. When using VACM, can map to a Security Name or Group Name of the entity running the test.

By default this will be set to

Example value: smokeping

packetsize

The packetsize parameter lets you configure the packet size for the pings sent. The minimum is 8, the maximum 65507. Use the same number as with fping if you want the same packet sizes being used on the network.

Default value: 56

pinghost

The (mandatory) pinghost parameter specifies the remote system which will execute the pings, as well as the SNMP community string on the device.

Example value: pinger@router.example.com

This setting is mandatory.

pingsrc

The (optional) pingsrc parameter specifies the source address to be used for pings. If specified, this parameter must identify an IP address assigned to pinghost.

Example value: 192.0.2.9

AUTHORS¶

Bill Fenner <fenner@research.att.com>, Tobi Oetiker <tobi@oetiker.ch>

NOTES¶

    snmp {
        view pingMIB {
            oid .1.3.6.1.2.1.80 include;
        }
        community pinger {
            view pingMIB;   
            authorization read-write;
            clients {
                192.0.2.134/32;
            }
        }
    }