Scroll to navigation

ping_iterator_get_info(3) liboping ping_iterator_get_info(3)

NAME

ping_iterator_get_info - Receive information about a host

SYNOPSIS

  #include <oping.h>
  int ping_iterator_get_info (pingobj_iter_t *iter,
                  int info,
                  void *buffer,
                  size_t *buffer_len);

DESCRIPTION

The ping_iterator_get_info method can be used on an host iterator to return various information about the current host.

The iter argument is an iterator as returned by ping_iterator_get(3) or ping_iterator_next(3).

The info argument specifies the type of information returned. Use the following defines:

Return the hostname of the host the iterator points to as supplied by the user. This is the name you passed to ping_host_add(3) and which you need to pass to "ping_host_remove", too.
Return the hostname of the host the iterator points to. Since the name is looked up using the socket address this may differ from the hostname passed to ping_host_add(3). The hostname is actually looked up every time you call this method, no cache is involved within liboping.

It is recommended to include "netdb.h" and allocate NI_MAXHOST bytes of buffer.

Return the address used in ASCII (i.e. human readable) format. The address is looked up every time you call this method. 40 bytes should be sufficient for the buffer (16 octets in hex format, seven colons and one null byte), but more won't hurt.
Returns the address family of the host. The buffer should be big enough to hold an integer. The value is either AF_INET or AF_INET6.
Return the last measured latency or less than zero if the timeout occurred before a echo response was received. The buffer should be big enough to hold a double value.
Return the number of times that no response was received within the timeout. This value is only increased but may wrap around at the 32 bit boundary. The buffer should be big enough to hold a 32 bit integer, e. g. an "uint32_t".
Return the last sequence number sent. This number is increased regardless of echo responses being received or not. The buffer should hold an integer.
Return the ident that is put into every ICMP packet sent to this host. Per convention this usually is the PID of the sending process, but since liboping can handle several hosts in parallel it uses a (pseudo-)random number here. The buffer should be big enough to hold an integer value.
Returns the time to live (TTL) of the received network packets. This number depends on the value that was used by the remote host when it sent the echo reply and has nothing to do with the PING_OPT_TTL of ping_setopt(3). The buffer should be big enough to hold an integer value.
Returns the value of the Quality of Service (QoS) byte of the incoming IPv4 or IPv6 packet. This byte is not interpreted by liboping at all and may be DSCP / ECN or precedence / ToS depending on your network setup. Please see the appropriate RFCs for further information on values you can expect to receive. The buffer is expected to an "uint8_t".

The buffer argument is a pointer to an appropriately sized area of memory where the result of the call will be stored. The buffer_len value is used as input and output: When calling ping_iterator_get_info it reports the size of the memory region pointed to by buffer. The method will write the number of bytes actually written to the memory into buffer_len before returning.

RETURN VALUE

ping_iterator_get_info returns zero if it succeeds.

EINVAL is returned if the value passed as info is unknown. Both, buffer and buffer_len, will be left untouched in this case.

If the requested information didn't fit into buffer then the size that would have been needed is written into buffer_len; buffer itself is left untouched. The return value is ENOMEM in this case.

SEE ALSO

ping_iterator_get(3), liboping(3)

AUTHOR

liboping is written by Florian "octo" Forster <ff at octo.it>. Its homepage can be found at <http://noping.cc/>.

Copyright (c) 2006-2017 by Florian "octo" Forster.

2024-10-15 1.10.0