NAME¶

vgscan — Search for all volume groups

SYNOPSIS¶

vgscan
[ option_args ]

DESCRIPTION¶

vgscan scans all supported LVM block devices in the system for VGs.

USAGE¶

vgscan

Common options for lvm:

OPTIONS¶

--commandprofile String
The command profile to use for command configuration. See lvm.conf(5) for more information about profiles.

--config String
Config settings for the command. These override lvm.conf(5) settings. The String arg uses the same format as lvm.conf(5), or may use section/field syntax. See lvm.conf(5) for more information about config.

-d|--debug ...
Set debug level. Repeat from 1 to 6 times to increase the detail of messages sent to the log file and/or syslog (if configured).

--devices PV
Restricts the devices that are visible and accessible to the command. Devices not listed will appear to be missing. This option can be repeated, or accepts a comma separated list of devices. This overrides the devices file.

--devicesfile String
A file listing devices that LVM should use. The file must exist in /etc/lvm/devices/ and is managed with the lvmdevices(8) command. This overrides the lvm.conf(5) devices/devicesfile and devices/use_devicesfile settings.

--driverloaded y|n
If set to no, the command will not attempt to use device-mapper. For testing and debugging.

-h|--help
Display help text.

--ignorelockingfailure
Allows a command to continue with read-only metadata operations after locking failures.

--journal String
Record information in the systemd journal. This information is in addition to information enabled by the lvm.conf log/journal setting. command: record information about the command. output: record the default command output. debug: record full command debugging.

--lockopt String
Used to pass options for special cases to lvmlockd. See lvmlockd(8) for more information.

--longhelp
Display long help text.

--mknodes
Also checks the LVM special files in /dev that are needed for active LVs and creates any missing ones and removes unused ones. See also additional --refresh option for use in udev environment.

--nohints
Do not use the hints file to locate devices for PVs. A command may read more devices to find PVs when hints are not used. The command will still perform standard hint file invalidation where appropriate.

--nolocking
Disable locking. Use with caution, concurrent commands may produce incorrect results.

--notifydbus
Send a notification to D-Bus. The command will exit with an error if LVM is not built with support for D-Bus notification, or if the notify_dbus config setting is disabled.

--profile String
An alias for --commandprofile or --metadataprofile, depending on the command.

-q|--quiet ...
Suppress output and log messages. Overrides --debug and --verbose. Repeat once to also suppress any prompts with answer 'no'.

--refresh
If the LV is active, reload its metadata. In an environment where udev is used to manage the /dev content, usage of this option is highly recommended. This is because refresh also regenerates udev events for an LV based on which existing udev rules are applied to set the /dev content and permissions. Also, this operation may be useful if something has gone wrong, or if some form of manual LV sharing is being used.

--reportformat basic|json|json_std
Overrides current output format for reports which is defined globally by the report/output_format setting in lvm.conf(5). basic is the original format with columns and rows. If there is more than one report per command, each report is prefixed with the report name for identification. json produces report output in JSON format. json_std produces report output in JSON format which is more compliant with JSON standard. See lvmreport(7) for more information.

-t|--test
Run in test mode. Commands will not update metadata. This is implemented by disabling all metadata writing but nevertheless returning success to the calling function. This may lead to unusual error messages in multi-stage operations if a tool relies on reading back metadata it believes has changed but hasn't.

-v|--verbose ...
Set verbose level. Repeat from 1 to 4 times to increase the detail of messages sent to stdout and stderr.

--version
Display version information.

-y|--yes
Do not prompt for confirmation interactively but always assume the answer yes. Use with extreme caution. (For automatic no, see -qq.)

VARIABLES¶

String

See the option description for information about the string content.

Size[UNIT]

Size is an input number that accepts an optional unit. Input units are always treated as base two values, regardless of capitalization, e.g. 'k' and 'K' both refer to 1024. The default input unit is specified by letter, followed by |UNIT. UNIT represents other possible input units: b|B is bytes, s|S is sectors of 512 bytes, k|K is KiB, m|M is MiB, g|G is GiB, t|T is TiB, p|P is PiB, e|E is EiB. (This should not be confused with the output control --units, where capital letters mean multiple of 1000.)

ENVIRONMENT VARIABLES¶

See lvm(8) for information about environment variables used by lvm. For example, LVM_VG_NAME can generally be substituted for a required VG parameter.

SEE ALSO¶

lvm(8), lvm.conf(5), lvmconfig(8), lvmdevices(8),

pvchange(8), pvck(8), pvcreate(8), pvdisplay(8), pvmove(8), pvremove(8), pvresize(8), pvs(8), pvscan(8),

vgcfgbackup(8), vgcfgrestore(8), vgchange(8), vgck(8), vgcreate(8), vgconvert(8), vgdisplay(8), vgexport(8), vgextend(8), vgimport(8), vgimportclone(8), vgimportdevices(8), vgmerge(8), vgmknodes(8), vgreduce(8), vgremove(8), vgrename(8), vgs(8), vgscan(8), vgsplit(8),

lvcreate(8), lvchange(8), lvconvert(8), lvdisplay(8), lvextend(8), lvreduce(8), lvremove(8), lvrename(8), lvresize(8), lvs(8), lvscan(8),

lvm-fullreport(8), lvm-lvpoll(8), blkdeactivate(8), lvmdump(8),

dmeventd(8), lvmpolld(8), lvmlockd(8), lvmlockctl(8), cmirrord(8), lvmdbusd(8), fsadm(8),

lvmsystemid(7), lvmreport(7), lvmcache(7), lvmraid(7), lvmthin(7), lvmvdo(7), lvmautoactivation(7)