Scroll to navigation

STRUCT SPI_MASTER(9) Serial Peripheral Interface (S STRUCT SPI_MASTER(9)

NAME

struct_spi_master - interface to SPI master controller

SYNOPSIS

struct spi_master {
  struct device dev;
  struct list_head list;
  s16 bus_num;
  u16 num_chipselect;
  u16 dma_alignment;
  u16 mode_bits;
  u32 bits_per_word_mask;
#define SPI_BPW_MASK(bits) BIT((bits) - 1)
#define SPI_BIT_MASK(bits) (((bits) == 32) ? ~0U : (BIT(bits) - 1))
#define SPI_BPW_RANGE_MASK(min# max) (SPI_BIT_MASK(max) - SPI_BIT_MASK(min - 1))
  u32 min_speed_hz;
  u32 max_speed_hz;
  u16 flags;
#define SPI_MASTER_HALF_DUPLEX	BIT(0)
#define SPI_MASTER_NO_RX	BIT(1)
#define SPI_MASTER_NO_TX	BIT(2)
#define SPI_MASTER_MUST_RX      BIT(3)
#define SPI_MASTER_MUST_TX      BIT(4)
  spinlock_t bus_lock_spinlock;
  struct mutex bus_lock_mutex;
  bool bus_lock_flag;
  int (* setup) (struct spi_device *spi);
  int (* transfer) (struct spi_device *spi,struct spi_message *mesg);
  void (* cleanup) (struct spi_device *spi);
  bool queued;
  struct kthread_worker kworker;
  struct task_struct * kworker_task;
  struct kthread_work pump_messages;
  spinlock_t queue_lock;
  struct list_head queue;
  struct spi_message * cur_msg;
  bool busy;
  bool running;
  bool rt;
  bool auto_runtime_pm;
  bool cur_msg_prepared;
  struct completion xfer_completion;
  size_t max_dma_len;
  int (* prepare_transfer_hardware) (struct spi_master *master);
  int (* transfer_one_message) (struct spi_master *master,struct spi_message *mesg);
  int (* unprepare_transfer_hardware) (struct spi_master *master);
  int (* prepare_message) (struct spi_master *master,struct spi_message *message);
  int (* unprepare_message) (struct spi_master *master,struct spi_message *message);
  void (* set_cs) (struct spi_device *spi, bool enable);
  int (* transfer_one) (struct spi_master *master, struct spi_device *spi,struct spi_transfer *transfer);
  int * cs_gpios;
};

MEMBERS

dev
device interface to this driver
list
link with the global spi_master list
bus_num
board-specific (and often SOC-specific) identifier for a given SPI controller.
num_chipselect
chipselects are used to distinguish individual SPI slaves, and are numbered from zero to num_chipselects. each slave has a chipselect signal, but it's common that not every chipselect is connected to a slave.
dma_alignment
SPI controller constraint on DMA buffers alignment.
mode_bits
flags understood by this controller driver
bits_per_word_mask
A mask indicating which values of bits_per_word are supported by the driver. Bit n indicates that a bits_per_word n+1 is supported. If set, the SPI core will reject any transfer with an unsupported bits_per_word. If not set, this value is simply ignored, and it's up to the individual driver to perform any validation.
min_speed_hz
Lowest supported transfer speed
max_speed_hz
Highest supported transfer speed
flags
other constraints relevant to this driver
bus_lock_spinlock
spinlock for SPI bus locking
bus_lock_mutex
mutex for SPI bus locking
bus_lock_flag
indicates that the SPI bus is locked for exclusive use
setup
updates the device mode and clocking records used by a device's SPI controller; protocol code may call this. This must fail if an unrecognized or unsupported mode is requested. It's always safe to call this unless transfers are pending on the device whose settings are being modified.
transfer
adds a message to the controller's transfer queue.
cleanup
frees controller-specific state
queued
whether this master is providing an internal message queue
kworker
thread struct for message pump
kworker_task
pointer to task for message pump kworker thread
pump_messages
work struct for scheduling work to the message pump
queue_lock
spinlock to syncronise access to message queue
queue
message queue
cur_msg
the currently in-flight message
busy
message pump is busy
running
message pump is running
rt
whether this queue is set to run as a realtime task
auto_runtime_pm
the core should ensure a runtime PM reference is held while the hardware is prepared, using the parent device for the spidev
cur_msg_prepared
spi_prepare_message was called for the currently in-flight message
xfer_completion
used by core transfer_one_message
max_dma_len
Maximum length of a DMA transfer for the device.
prepare_transfer_hardware
a message will soon arrive from the queue so the subsystem requests the driver to prepare the transfer hardware by issuing this call
transfer_one_message
the subsystem calls the driver to transfer a single message while queuing transfers that arrive in the meantime. When the driver is finished with this message, it must call spi_finalize_current_message so the subsystem can issue the next message
unprepare_transfer_hardware
there are currently no more messages on the queue so the subsystem notifies the driver that it may relax the hardware by issuing this call
prepare_message
set up the controller to transfer a single message, for example doing DMA mapping. Called from threaded context.
unprepare_message
undo any work done by prepare_message.
set_cs
set the logic level of the chip select line. May be called from interrupt context.
transfer_one
transfer a single spi_transfer. - return 0 if the transfer is finished, - return 1 if the transfer is still in progress. When the driver is finished with this transfer it must call spi_finalize_current_transfer so the subsystem can issue the next transfer. Note: transfer_one and transfer_one_message are mutually exclusive; when both are set, the generic subsystem does not call your transfer_one callback.
cs_gpios
Array of GPIOs to use as chip select lines; one per CS number. Any individual value may be -ENOENT for CS lines that are not GPIOs (driven by the SPI controller itself).

DESCRIPTION

Each SPI master controller can communicate with one or more spi_device children. These make a small bus, sharing MOSI, MISO and SCK signals but not chip select signals. Each device may be configured to use a different clock rate, since those shared signals are ignored unless the chip is selected.
The driver for an SPI controller manages access to those devices through a queue of spi_message transactions, copying data between CPU memory and an SPI slave device. For each such message it queues, it calls the message's completion function when the transaction completes.

COPYRIGHT

February 2017 Kernel Hackers Manual 3.16