NAME¶

cciss - HP Smart Array block driver

SYNOPSIS¶

modprobe cciss [ cciss_allow_hpsa=1 ]

DESCRIPTION¶

cciss is a block driver for older HP Smart Array RAID controllers.

Options¶

cciss_allow_hpsa=1: This option prevents the cciss driver from attempting to drive any controllers that the hpsa(4) driver is capable of controlling, which is to say, the cciss driver is restricted by this option to the following controllers:

    Smart Array 5300
    Smart Array 5i
    Smart Array 532
    Smart Array 5312
    Smart Array 641
    Smart Array 642
    Smart Array 6400
    Smart Array 6400 EM
    Smart Array 6i
    Smart Array P600
    Smart Array P400i
    Smart Array E200i
    Smart Array E200
    Smart Array E200i
    Smart Array E200i
    Smart Array E200i
    Smart Array E500

Supported Hardware¶

The cciss driver supports the following Smart Array boards:

    Smart Array 5300
    Smart Array 5i
    Smart Array 532
    Smart Array 5312
    Smart Array 641
    Smart Array 642
    Smart Array 6400
    Smart Array 6400 U320 Expansion Module
    Smart Array 6i
    Smart Array P600
    Smart Array P800
    Smart Array E400
    Smart Array P400i
    Smart Array E200
    Smart Array E200i
    Smart Array E500
    Smart Array P700m
    Smart Array P212
    Smart Array P410
    Smart Array P410i
    Smart Array P411
    Smart Array P812
    Smart Array P712m
    Smart Array P711m

Configuration Details¶

To configure HP Smart Array controllers, use the HP Array Configuration Utility (either hpacuxe(8) or hpacucli(8)) or the Offline ROM-based Configuration Utility (ORCA) run from the Smart Array's option ROM at boot time.

FILES¶

Device Nodes¶

The device naming scheme is as follows:

Major numbers:

    104     cciss0
    105     cciss1
    106     cciss2
    105     cciss3
    108     cciss4
    109     cciss5
    110     cciss6
    111     cciss7

Minor numbers:

    b7 b6 b5 b4 b3 b2 b1 b0
    |----+----| |----+----|
         |           |
         |           +-------- Partition ID (0=wholedev, 1-15 partition)
         |
         +-------------------- Logical Volume number

The device naming scheme is:

    /dev/cciss/c0d0         Controller 0, disk 0, whole device
    /dev/cciss/c0d0p1       Controller 0, disk 0, partition 1
    /dev/cciss/c0d0p2       Controller 0, disk 0, partition 2
    /dev/cciss/c0d0p3       Controller 0, disk 0, partition 3

    /dev/cciss/c1d1         Controller 1, disk 1, whole device
    /dev/cciss/c1d1p1       Controller 1, disk 1, partition 1
    /dev/cciss/c1d1p2       Controller 1, disk 1, partition 2
    /dev/cciss/c1d1p3       Controller 1, disk 1, partition 3

Files in /proc¶

The files /proc/driver/cciss/cciss[0-9]+ contain information about the configuration of each controller. For example:

    $  cd /proc/driver/cciss
    $  ls -l
    total 0
    -rw-r--r-- 1 root root 0 2010-09-10 10:38 cciss0
    -rw-r--r-- 1 root root 0 2010-09-10 10:38 cciss1
    -rw-r--r-- 1 root root 0 2010-09-10 10:38 cciss2
    $  cat cciss2
    cciss2: HP Smart Array P800 Controller
    Board ID: 0x3223103c
    Firmware Version: 7.14
    IRQ: 16
    Logical drives: 1
    Current Q depth: 0
    Current # commands on controller: 0
    Max Q depth since init: 1
    Max # commands on controller since init: 2
    Max SG entries since init: 32
    Sequential access devices: 0

    cciss/c2d0:   36.38GB       RAID 0

Files in /sys¶

/sys/bus/pci/devices/<dev>/ccissX/cXdY/model

Displays the SCSI INQUIRY page 0 model for logical drive Y of controller X.

/sys/bus/pci/devices/<dev>/ccissX/cXdY/rev

Displays the SCSI INQUIRY page 0 revision for logical drive Y of controller X.

/sys/bus/pci/devices/<dev>/ccissX/cXdY/unique_id

Displays the SCSI INQUIRY page 83 serial number for logical drive Y of controller X.

/sys/bus/pci/devices/<dev>/ccissX/cXdY/vendor

Displays the SCSI INQUIRY page 0 vendor for logical drive Y of controller X.

/sys/bus/pci/devices/<dev>/ccissX/cXdY/block:cciss!cXdY

A symbolic link to /sys/block/cciss!cXdY.

/sys/bus/pci/devices/<dev>/ccissX/rescan

When this file is written to, the driver rescans the controller to discover any new, removed, or modified logical drives.

/sys/bus/pci/devices/<dev>/ccissX/resettable

A value of 1 displayed in this file indicates that the "reset_devices=1" kernel parameter (used by kdump) is honored by this controller. A value of 0 indicates that the "reset_devices=1" kernel parameter will not be honored. Some models of Smart Array are not able to honor this parameter.

/sys/bus/pci/devices/<dev>/ccissX/cXdY/lunid

Displays the 8-byte LUN ID used to address logical drive Y of controller X.

/sys/bus/pci/devices/<dev>/ccissX/cXdY/raid_level

Displays the RAID level of logical drive Y of controller X.

/sys/bus/pci/devices/<dev>/ccissX/cXdY/usage_count

Displays the usage count (number of opens) of logical drive Y of controller X.

SCSI tape drive and medium changer support¶

SCSI sequential access devices and medium changer devices are supported and appropriate device nodes are automatically created (e.g., /dev/st0, /dev/st1, etc.; see st(4) for more details.) You must enable "SCSI tape drive support for Smart Array 5xxx" and "SCSI support" in your kernel configuration to be able to use SCSI tape drives with your Smart Array 5xxx controller. Additionally, note that the driver will not engage the SCSI core at init time. The driver must be directed to dynamically engage the SCSI core via the /proc file-system entry, which the "block" side of the driver creates as /proc/driver/cciss/cciss* at runtime. This is because at driver init time, the SCSI core may not yet be initialized (because the driver is a block driver) and attempting to register it with the SCSI core in such a case would cause a hang. This is best done via an initialization script (typically in /etc/init.d, but could vary depending on distribution). For example:

    for x in /proc/driver/cciss/cciss[0-9]*
    do
        echo "engage scsi" > $x
    done

Once the SCSI core is engaged by the driver, it cannot be disengaged (except by unloading the driver, if it happens to be linked as a module.) Note also that if no sequential access devices or medium changers are detected, the SCSI core will not be engaged by the action of the above script.

Hot plug support for SCSI tape drives¶

Hot plugging of SCSI tape drives is supported, with some caveats. The cciss driver must be informed that changes to the SCSI bus have been made. This may be done via the /proc file system. For example:
echo "rescan" > /proc/scsi/cciss0/1 This causes the driver to: The driver will output messages indicating which devices have been added or removed and the controller, bus, target and lun used to address each device. The driver then notifies the SCSI midlayer of these changes. Note that the naming convention of the /proc file-system entries contains a number in addition to the driver name (e.g., "cciss0" instead of just "cciss", which you might expect). Note: Only sequential access devices and medium changers are presented as SCSI devices to the SCSI midlayer by the cciss driver. Specifically, physical SCSI disk drives are not presented to the SCSI midlayer. The only disk devices that are presented to the kernel are logical drives that the array controller constructs from regions on the physical drives. The logical drives are presented to the block layer (not to the SCSI midlayer). It is important for the driver to prevent the kernel from accessing the physical drives directlyi, since these drives are used by the array controller to construct the logical drives.

SCSI error handling for tape drives and medium changers¶

The Linux SCSI midlayer provides an error-handling protocol that is initiated whenever a SCSI command fails to complete within a certain amount of time (which can vary depending on the command). The cciss driver participates in this protocol to some extent. The normal protocol is a four-step process:

*

First, the device is told to abort the command.

*

If that doesn't work, the device is reset.

*

If that doesn't work, the SCSI bus is reset.

*

If that doesn't work the host bus adapter is reset.

The cciss driver is a block driver as well as a SCSI driver and only the tape drives and medium changers are presented to the SCSI midlayer Furthermore, unlike more straightforward SCSI drivers, disk I/O continues through the block side during the SCSI error-recovery process Therefore, the cciss driver implements only the first two of these actions, aborting the command, and resetting the device. Note also that most tape drives will not oblige in aborting commands, and sometimes it appears they will not even obey a reset command, though in most circumstances they will. If the command cannot be aborted and the device cannot be reset, the device will be set offline. In the event that the error-handling code is triggered and a tape drive is successfully reset or the tardy command is successfully aborted, the tape drive may still not allow I/O to continue until some command is issued that positions the tape to a known position. Typically you must rewind the tape (by issuing mt -f /dev/st0 rewind for example) before I/O can proceed again to a tape drive that was reset.

SEE ALSO¶

cciss_vol_status(8), hpsa(4), hpacucli(8), hpacuxe(8), http://cciss.sf.net and Documentation/blockdev/cciss.txt and Documentation/ABI/testing/sysfs-bus-pci-devices-cciss in the Linux kernel source tree

COLOPHON¶

This page is part of release 3.44 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/.